PThe ColorMaster2 driver is identical to the ColorMaster driver except it is approximately twice as fast during color graphics printing, and requires a lot of memory (up to about 1.2 Megabytes for a full 8.5 by 11 inch color graphics print). The memory requirements are one third of this when doing black & white or grey scale printing.FSCC
CBM MPS1000
Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 13.6 inches. Two densities are supported: 120 and 240 dpi.
Diablo C-150PARA
Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 8.5 inches.PARA
EpsonQPARA
bFor both black & white and color Epson LQ series printers. Uses a 24 pin graphics print mode. Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 13.6 inches. Four densities are supported: 90, 120, 180, and 360 dpi.PARA
EpsonXPARA
LFor both black & white and color Epson EX, FX, JX, LX, MX, and RX series printers. Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 13.6 inches. Two densities are supported: 120, and 240 dpi.PARA
HP LaserJet
qFor LaserJet, LaserJet Plus, and LaserJet II printers. Four densities are supported: 75, 100, 150, and 300 dpi.
HP PaintJet
No special provisions.PARA
ImageWriter IIFSCC
HSeven densities are supported: 80, 96, 107, 120, 136, 144, and 160 dpi.PARA
Okidata 293IFSCC
YFor both the Okidata 292 and 293 with IBM interface modules. Uses a 16 pin graphics print mode. Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 13.6 inches. Two densities are supported: 120 and 240 dpi.
Okidata 92PARA
No special provisions.PARA
Okimate 20PARA
No special provisions.PARA
Xerox 4020PARA
:This driver is identical to the Diablo C-150 driver except it prints all black dots twice. This is a special feature of this printer and produces much more solid and darker black shades. Note that there is some increase in printing time as a result of this feature--if you don't want it then use the Diablo C-150 driver. Assumes 8.5 inch wide paper with a printable width of 8.0 inches, unless a paper type of "Wide Tractor" is selected from Preferences in which case it assumes a maximum printable width of 9.0 inches. Two densities are supported: 120 and 240 dpi.FSCC
Additional NotesPARA
Some Epson and Epson compatible printer's line spacing is a bit sloppy. If you notice tiny white lines between each vertical strip of 8 dots try selecting a paper type of "Single" (rather than "Fanfold") in Preferences. This tells the printer driver to advance 23/216 of a inch instead of the standard 24/216 of a inch. This option has been implemented on the EpsonX, and CBM MPS-1000 drivers.HEAD